GoalExplain why a circuit needs a fuse or a circuit breaker, how each works, and how the rating of a fuse is chosen. These are explained only: they are for adults to handle.
New words
fuse · a thin wire in a case that melts and breaks the circuit if the current gets too highfuse rating · the largest current a fuse can carry without melting, in amperes (A)circuit breaker · an automatic switch that opens when the current is too high and can be reset after the fault is put rightshort circuit · an accidental path of very low resistance that lets a very large current flow
Explanation
A current makes the wires it flows through warm up, and a very large current can make them hot enough to start a fire. A current can become too large when too many devices are joined in parallel to one supply, because each branch adds its current. It can also become too large when a fault gives the current a short cut of very low resistance, a short circuit: since I = V ÷ R, a very small R gives a very large I. A fuse is connected in series with the device it protects. It contains a thin wire with a rating. If the current rises above the rating, the thin wire gets hot and melts, the circuit is broken, and the current stops. A blown fuse must be replaced, by an adult, after the fault is found. A circuit breaker does the same job with a switch that opens by itself, and it can be reset. In diagrams a fuse is drawn as a box with a line through it; the pictures here label a plain box ‘fuse’. Choose the smallest available rating that is above the normal current. Never open a plug or a socket, never replace a fuse yourself, and never use a fuse of the wrong rating.
the current becomes too large→the thin wire of the fuse heats up→the fuse wire melts→the circuit is broken→the current stops
Worked examples
Device
Normal current
Fuse to choose
table lamp
0.3 A
3 A
toaster
4.2 A
5 A
TV
1.2 A
3 A
fan heater
8.5 A
13 A
Choosing a fuse. Common fuse ratings are 3 A, 5 A and 13 A. The rating must be above the normal current, and as close above it as the ratings available allow, so that the fuse protects the device.
A fuse in a circuit. The fuse is in series with the lamp. If a fault makes the current too large, the fuse wire melts and the lamp goes out because the circuit is open.
Resistance
Current = 12 V ÷ R
normal path through the device
24 Ω
0.5 A
short cut (fault)
0.24 Ω
50 A
A short circuit. A supply of 12 V drives a device of 24 Ω. A damaged wire makes a short cut of only 0.24 Ω, 100 times less. The current becomes 12 ÷ 0.24 = 50 A instead of 12 ÷ 24 = 0.5 A, 100 times larger. A fuse or a circuit breaker stops it. (Real supplies limit the current, but it is still far too large.)
Class activity
The weakest link. A paper model of a fuse, with no electricity. With an adult. The adult cuts three strips of thin card or paper, each 20 cm long and 3 cm wide. The adult also cuts a notch on both sides of each strip at the middle, leaving a narrow neck of 2 cm, 1 cm and 0.5 cm. Tape each strip between two chairs, or hold the ends, and hang a paper cup in the middle on a loop of string. Add coins to the cup one at a time and count how many each strip holds before it tears. Do this over a cushion. Record the numbers in a table. The narrowest neck tears first, just as the thin wire of a fuse melts first. What is the strip’s ‘rating’? What does the model leave out? (A real fuse melts because of heat, not because of a pull.) A fuse has to be replaced after it has ‘blown’. Does the torn strip?
Practice
1
Why must a fuse be placed one after the other with the device to protect it, instead of across it?
In series, all the current to the device passes through the fuse, so it melts if the current is too large. Joined across the device, the fuse would be a short circuit round it: the current would take that easy path and the device would not be protected.
2
Choose a fuse from 3 A, 5 A and 13 A for each device. (a) 1.2 A (b) 4.6 A (c) 11 A (d) 5.5 A. Give the rule you used.
Device
Normal current
a
1.2 A
b
4.6 A
c
11 A
d
5.5 A
(a) 3 A (b) 5 A (c) 13 A (d) 13 A. Take the smallest rating that is above the normal current; 5 A would melt for the 5.5 A device.
3
Each of the three lamps takes 2.0 A. The fuse in the main wire is rated 5 A. The lamps have their own switches (not drawn). How many lamps can be on at once without the fuse melting?
Two lamps: 2 × 2.0 = 4.0 A is below 5 A. Three lamps would need 6.0 A, which is more than 5 A, so the fuse would melt.
4
Omar’s fuse keeps melting, so he suggests replacing it with a stronger one or a piece of metal foil. Explain why this is dangerous, and what should be done instead.
The fuse melts because the current is too large, and a bigger fuse or foil would let the wires overheat and cause a fire. An adult should find the cause (a fault or too many devices) and use the right fuse.