Parallel circuits; current and voltage in parallel circuits
Week 33 · Unit 9 · 9.1–9.2 · 3 lessons
1
Two paths for the current
Workbook 9: Topics 9.1–9.2, pp. 172–179
GoalTell a parallel circuit from a series circuit and use the rule that the currents in the branches add up to the current from the cell.
New words
parallel circuit · a circuit in which the current has more than one path from the cell and back to itbranch · one of the separate paths in a parallel circuitjunction · a point where the wire splits into branches, or where the branches join againammeter · a meter that measures current in amperes (A); it is connected in series with the part you are testing
Explanation
In a series circuit there is only one path, so the same current passes through every component, and one break stops the whole circuit. In a parallel circuit the wire splits at a junction into two or more branches, and the branches join again before the wire returns to the cell. The current from the cell divides at the first junction, and the currents add up again at the second. So the current from the cell is the sum of the currents in the branches: I(cell) = I₁ + I₂ + … Current is not used up: whatever flows into a junction flows out of it. Identical branches carry equal currents. Branches with different parts carry different currents, and the part that lets more current through takes the larger share. If one branch is broken, the other branches still have a complete path and keep working. To measure the current in a branch, put an ammeter in that branch, in series.
Worked examples
Two identical lamps in parallel. The ammeter next to the cell reads 0.80 A. Identical branches share the current equally, so each lamp branch carries 0.80 ÷ 2 = 0.40 A.
Three different branches: a motor (M), a lamp and a buzzer. The currents in the branches add up to the current from the cell: 0.50 + 0.30 + 0.20 = 1.00 A.
Current in L₁
Current in L₂
Current from the cell
both lamps working
0.40 A
0.40 A
0.80 A
L₂ unscrewed
0.40 A
0 A
0.40 A
What happens when one branch breaks? Lamp L₂ of the first example is unscrewed. L₁ still has a complete path, so its current does not change, and the cell now supplies only one branch. In a series circuit, unscrewing one lamp would put both out.
Class activity
Bulbs in series and in parallel. With an adult. You need one AA cell (1.5 V), two identical small torch bulbs (1.5 V, in holders if you have them), and short wires, or paper clips and foil, to join them. Only use a standard small cell, never a socket. Predict first. (1) Light one bulb alone and note its brightness. (2) Join the two bulbs one after the other in a single loop (series). (3) Rebuild so that each bulb is joined straight across the cell by its own pair of wires (parallel). (4) In each arrangement, loosen one bulb and watch the other. Keep each circuit connected for only a few seconds, because wires and cells can warm up. Record ‘as bright as one bulb’, ‘dimmer’ or ‘out’ in a table. Expected: series bulbs are dimmer and both go out; parallel bulbs are about as bright as one alone (a worn cell may make them a little dimmer) and the other stays lit. Why would the cell go flat sooner in the parallel circuit?
Practice
1
A pupil says: ‘In a parallel circuit the first lamp uses up some of the current, so the second lamp gets less.’ Correct the statement.
Current is not used up. It divides at the junction, each branch has its own current, and the branch currents add up to the current from the cell. With identical lamps the two branches carry equal currents.
2
Three lamps are in parallel. The ammeter at the cell reads 1.2 A, and the ammeters in two branches read 0.5 A and 0.4 A. Find the current in the third branch. Show your working.
A string of old fairy lights goes completely dark when one bulb is taken out. Are the bulbs in series or in parallel? Explain, and say how a designer could change the string so that the others stay lit.
In series: there is one path, so removing a bulb breaks the circuit for all. If each bulb were in its own branch (in parallel) the others would stay lit.
4
The ammeter A₁ in the main wire reads 0.90 A. The lamp branch carries twice as much current as the buzzer branch. Find the readings of A₂ (lamp) and A₃ (buzzer).
Call the buzzer current b. Then b + 2b = 0.90 A, so b = 0.30 A. A₃ = 0.30 A and A₂ = 0.60 A (0.60 + 0.30 = 0.90 A).