GoalReview series and parallel circuits, resistance, variable resistors, fuses and switches with new problems.
New words
series circuit · a circuit with one path: the same current everywhere and the voltage shared between the componentsparallel circuit · a circuit with branches: the branch currents add up to the cell current and each branch has the cell voltageresistance · R = V ÷ I, measured in ohms; a longer or thinner wire has morefuse · a thin wire that melts and breaks the circuit when the current is above its rating
Explanation
In a series circuit the current is the same everywhere and the voltage is shared between the components. In a parallel circuit the current splits at a junction, the branch currents add up to the current from the cell, and every branch has the full cell voltage. An ammeter goes in series and a voltmeter goes across a component. Resistance is voltage ÷ current in ohms, so V = I × R and I = V ÷ R. The same voltage gives a smaller current through a larger resistance. A wire has more resistance when it is longer or thinner, and the resistance depends on the material. A variable resistor in series with a lamp or motor changes the current. A fuse in series melts when the current is above its rating; a circuit breaker does the same job and can be reset. Switches in series need both closed; switches in parallel need only one closed; a switch in each branch controls each lamp separately.
Series
Parallel
current
same everywhere
branch currents add up
voltage
shared
same across every branch
resistance
R = V ÷ I
each branch: I = V ÷ R
one part fails
everything stops
other branches carry on
Worked examples
Resistors in parallel. A 12 V cell is joined to a 20 Ω and a 30 Ω resistor in parallel. Each branch has 12 V, so the currents are 12 ÷ 20 = 0.60 A and 12 ÷ 30 = 0.40 A. The cell supplies 0.60 + 0.40 = 1.00 A.
Series
Parallel
current from the cell
0.25 A
1.00 A
voltage across one resistor
3 V
6 V
current in one resistor
0.25 A
0.50 A
Series or parallel with the same parts. A 6 V cell and two identical 12 Ω resistors. In series the total resistance is 24 Ω, so the current is 0.25 A. In parallel each resistor has 6 V and takes 0.50 A, so the cell supplies 1.00 A.
Job
Part or arrangement
change the loudness of a speaker smoothly
variable resistor in series
stop a current that is too large, and replace the part after
fuse (explained only; an adult replaces it)
a bell that rings if either button is pressed
two switches in parallel
a machine that needs two conditions
two switches in series
Choosing a part for the job.
Class activity
Predict the reading. Two players, a die, paper and a calculator. Roll the die for the cell voltage: 1 or 2 means 3 V, 3 or 4 means 6 V, 5 or 6 means 12 V. Draw three parallel branches with a resistor in each, and fill them from a bag of cards marked 10 Ω, 20 Ω, 30 Ω and 60 Ω (put each card back after drawing). The other player predicts the current in each branch (V ÷ R) and the current from the cell, then checks with the calculator. 1 point for each correct branch, 2 for the cell current. Twist cards: ‘one branch breaks’ (find the new cell current) and ‘there is a 1 A fuse in the main wire’ (does it melt?). First to 15 points wins. Why do all the numbers come out exactly, and what would happen to the cell current if a fourth branch was added?
Practice
1
A 9 V cell is joined to an 18 Ω and a 45 Ω resistor in parallel. Find the current in each branch and the current from the cell.
9 ÷ 18 = 0.50 A and 9 ÷ 45 = 0.20 A. The cell supplies 0.50 + 0.20 = 0.70 A.
2
A 12 V system has three lamps in parallel taking 1.5 A, 2.5 A and 3.0 A. A fuse in the main wire is to be chosen from 5 A, 10 A and 15 A. Which one, and why?
The total is 1.5 + 2.5 + 3.0 = 7.0 A. The 10 A fuse: above 7.0 A, so it will not melt when all are on, but close enough to protect the circuit. A 5 A fuse would melt, and 15 A would be too far above the normal current.
3
A 40 cm length of a thin nichrome wire has a resistance of 8 Ω. Find the resistance of (a) 80 cm of the same wire and (b) 40 cm of a wire of the same metal with four times the cross-section.
(a) 16 Ω, because the length is doubled. (b) 8 ÷ 4 = 2 Ω, because the area is four times larger.
4
Lola puts a variable resistor in series with a 20 Ω buzzer on a 6 V cell. With the variable resistor at 10 Ω the ammeter reads 0.20 A, and at 30 Ω it reads 0.12 A. Find the total resistance each time, check that the buzzer’s resistance is the same, and say which setting is louder.
Total resistance 6 ÷ 0.20 = 30 Ω and 6 ÷ 0.12 = 50 Ω. Take away the variable resistor: 30 − 10 = 20 Ω and 50 − 30 = 20 Ω, so the buzzer’s resistance is the same. The 10 Ω setting gives the larger current, so it is louder.