GoalExplain how the length, thickness and material of a wire change its resistance, and use data from a wire investigation.
New words
resistance wire · a wire, such as nichrome, that has a high resistance for its sizecross-section · the shape you see if you cut a wire straight across; a thicker wire has a larger cross-sectioncontrol variable · a quantity that is kept the same in a fair testdirectly proportional · when one quantity doubles, the other doubles, so a graph of the two is a straight line through zero
Explanation
The resistance of a wire depends on three things. A longer wire has more resistance: twice the length gives twice the resistance. A thinner wire has more resistance: a wire with twice the cross-section has half the resistance. The material matters too: copper has a very low resistance, while nichrome, an alloy of nickel and chromium, has a high one. A model helps: water flows more easily through a short, wide pipe than through a long, narrow one. In metals, the moving charges collide with the atoms of the metal, and a longer path has more collisions, while a thicker wire gives them more room to get through. In an investigation of length, change the length of one wire, measure the voltage and the current each time, and calculate R = V ÷ I. Keep the wire, its thickness and the voltage the same. Switch off between readings, because a wire that warms up has a higher resistance and would change the result.
What changes
Effect on the resistance of a wire
longer wire
greater
thicker wire (larger cross-section)
smaller
a different material
copper low, nichrome high
wire warms up
greater (so keep the current off between readings)
Worked examples
A teacher’s results. The same nichrome wire with a 3.0 V supply. R = V ÷ I each time. The points lie on a straight line through zero, so the resistance is directly proportional to the length.
Length (cm)
Current (A)
Resistance (Ω)
25
1.20
2.5
50
0.60
5.0
75
0.40
7.5
100
0.30
10.0
The readings behind the graph.
1 m of wire
Cross-section
Resistance
nichrome, thin
0.1 mm²
about 12 Ω
nichrome, 2 × thicker
0.2 mm²
about 6 Ω
nichrome, 4 × thicker
0.4 mm²
about 3 Ω
copper, 0.2 mm²
0.2 mm²
about 0.09 Ω
iron, 0.2 mm²
0.2 mm²
about 0.5 Ω
Thickness and material (typical values, 1 m long). Each time the area doubles, the resistance halves. A heating element is made of nichrome because its high resistance makes it heat up; the connecting wires are copper because their low resistance wastes little energy.
Class activity
Pencil-line resistance. With an adult who has a multimeter with an ohm (Ω) range. The meter must never be used on a cell, a plug or anything that has electricity in it. On a plain sheet of paper, use a soft pencil (2B or softer) to draw a rectangle 5 cm long and 1 cm wide and colour it in thickly and evenly. The adult holds the meter probes on the graphite 1 cm, 2 cm, 3 cm and 4 cm apart, pressing equally hard each time. The meter may show kΩ (1 kΩ = 1000 Ω): use the same range every time. Repeat each reading and note any odd one. Then draw a second rectangle, 5 cm long and 0.5 cm wide, and measure over 4 cm. Plot resistance against distance. What do you expect for the narrower strip? What could make your readings differ (pressure of the probes, thickness of the pencil layer)? No meter? Plan the investigation on paper with a table of results.
Practice
1
A 3.0 V supply is joined across different lengths of the same wire. Calculate the resistance of each length, state the pattern, and predict the resistance of 150 cm.
Length (cm)
Current (A)
30
1.00
60
0.50
120
0.25
R = 3.0 ÷ 1.00 = 3 Ω, 3.0 ÷ 0.50 = 6 Ω, 3.0 ÷ 0.25 = 12 Ω. Doubling the length doubles the resistance. 150 cm is 5 times 30 cm, so about 5 × 3 = 15 Ω.
2
Four copper wires: P is 1 m long and thin; Q is 2 m long and thin; R is 1 m long and twice as thick as P; S is 2 m long and twice as thick as P. Put them in order from the smallest to the greatest resistance.
Wire
Length
Thickness
P
1 m
thin
Q
2 m
thin
R
1 m
twice P
S
2 m
twice P
R (0.5 units), then P and S together (1 unit each), then Q (2 units). Check: R has double the area so half of P; S is double the length and double the area so the same as P; Q is double the length so double.
3
Why is the heating element of a kettle or toaster made of nichrome wire and not copper wire?
Nichrome has a much higher resistance, so for the same current it heats up much more; copper’s resistance is so low that it would hardly warm. Nichrome also does not melt or burn away easily in use.
4
A pupil leaves the current on for a whole minute while measuring a wire, and finds that the ammeter reading slowly falls. Explain this, and say how to improve the method.
The wire warms up, its resistance rises, so with the same voltage the current falls. Switch off between readings (or take each reading quickly) so that the temperature stays about the same.