GoalPlan and evaluate an investigation of pressure and apply the idea to everyday designs.
New words
investigation · a plan to answer a scientific question by testingaccuracy · how close a measurement is to the true valuecontrol variable · something kept the same to make the test fairtrend · the general pattern in the results
Explanation
Pressure ideas can be tested. Put a box on its three different faces and the force stays the same, because the weight of the box does not change. Only the contact area changes, so the area is the independent variable and the pressure is calculated from it. You can also see the effect by looking at how deeply the box sinks into clay or flour, which is the dependent variable you observe. To make the test fair, use the same box and the same surface and press the box down gently without pushing. Measure the sides with a ruler to the nearest millimetre and the mass on a scale, repeat the measurements, and calculate the mean. The results show a trend: the smaller the area, the greater the pressure. Link it to designs, such as tank tracks and the sharp edge of a knife.
Worked examples
Face
Area (cm²)
Pressure (N/cm²)
large (30 × 20)
600
0.02
medium (30 × 3)
90
0.13
small (20 × 3)
60
0.20
Amir weighs a textbook (1.2 kg, so 12 N) and measures its faces. He calculates the pressure for each way of standing it on a table.
Edge (cm)
Area (cm²)
Pressure (N/cm²)
Amir’s reading
3.0
60
0.20
more careful reading
3.2
64
0.19
Why accuracy matters: Amir measures the 3 cm edge of the book as 3.0 cm, but it is really 3.2 cm. His small-face area comes out as 60 cm² instead of 64 cm², so he calculates 0.20 N/cm² instead of 0.19 N/cm². A small slip in a measurement gives a small slip in the answer, so measure to the nearest millimetre.
Design with pressure: a snowshoe has a large area, a skater’s blade a small area, a tank has wide tracks and a cheese wire has a thin edge.
Class activity
Dent investigation with an adult. Fill a baking tray 3 cm deep with flour or damp sand and smooth the top. Take a small box (such as a tea box) filled so it weighs about 500 g. Place it very gently on its large face, lift it straight off and measure the depth of the dent with a ruler or a straw. Smooth the surface again and repeat with the medium and small faces. Predict first. Repeat each face three times and find the mean depth. Which variable did you change, which did you measure and which two did you keep the same? Write a conclusion linking dent depth to pressure and area. Clean up with the adult.
Practice
1
Complete the table by calculating the pressure on each face of a 15 N box.
Face
Area (cm²)
Pressure (N/cm²)
A
5
?
B
30
?
C
150
?
Face A: 15 ÷ 5 = 3 N/cm². Face B: 15 ÷ 30 = 0.5 N/cm². Face C: 15 ÷ 150 = 0.1 N/cm².
2
Explain why a heavy truck on soft sand has wide tyres or even several pairs of tyres.
The weight is spread over a larger area, so the pressure is smaller and the truck sinks less.
3
In the dent investigation, name the independent variable, the dependent variable and two control variables.
Independent: the face of the box (the contact area). Dependent: the depth of the dent. Control: the box and its weight, the flour or sand and how smooth and deep it is, how gently the box is placed.
4
Suggest two ways to make the results of the pressure investigation more accurate.
Measure each side more than once and use the mean, measure to the nearest millimetre, weigh the box on a better scale, repeat the dent test and find the mean, and keep the surface smooth.