GoalCalculate speeds from distance–time graphs, and plan, record and analyse a speed investigation.
New words
average speed of a journey · total distance divided by total time, including stopsrepeat · doing a measurement again to check it and to spot mistakesmean · the sum of the values divided by how many there areanomalous result · a result that does not fit the pattern of the others
Explanation
To find a speed from a distance–time graph, choose one straight section. Read how far the distance changed and how long the time changed, then divide: speed = distance ÷ time. A steeper section gives a bigger answer. To find the average speed of the whole journey, divide the total distance by the total time, stops included. Speeds can also be investigated by experiment. If you roll a toy car down a ramp carrying different numbers of coins, the load is the independent variable, the speed is the dependent variable, and the ramp, the car and the distance timed are control variables. Repeat each timing, because a stopwatch is started and stopped by a human with a reaction time. Calculate the mean, ignore any anomalous result (and say so), plot a line graph and describe the trend.
Worked examples
Section
Distance (m)
Time (s)
Speed (m/s)
first
40
20
2
stop
0
10
0
last
60
20
3
whole journey
100
50
2
From the graph: first section 40 m in 20 s = 2 m/s. Stationary for 10 s. Last section 60 m in 20 s = 3 m/s. Whole journey: 100 m in 50 s = 2 m/s.
Coins carried
Mean time (s)
Speed (m/s)
0
0.80
1.25
2
0.78
1.28
4
0.81
1.23
6
0.79
1.27
Aisha rolls a toy car down the same ramp carrying 0, 2, 4 and 6 coins and times it over a 1.0 m flat track. She calculates speed = 1.0 ÷ mean time for each load.
Plotting her results gives an almost flat line: the speeds are all close to 1.25 m/s. She concludes that the load has little effect on the speed, and she says that the small differences are probably timing errors.
Class activity
Ramp investigation with an adult. Prop a smooth board on books to make a ramp and put a toy car at the top. Mark a flat track of 1 m on the floor beyond the ramp end. Predict whether adding coins to the car will change its speed. Release the car without pushing it, and time it over the 1 m with a phone stopwatch. Use 0, 2, 4 and 6 coins taped firmly to the car, and repeat each load three times. Make a results table, calculate the mean time and the speed, and plot a line graph. Name the independent, dependent and control variables. Keep fingers clear of the books and do not run on the track.
Practice
1
Use the graph to calculate the speed of the first section, the speed of the last section and the average speed for the whole journey.
Ben times a toy car over 1 m three times: 0.9 s, 0.8 s and 1.6 s. Which result is anomalous? Calculate the mean time without it and suggest a cause.
Try
Time (s)
1
0.9
2
0.8
3
1.6
1.6 s is anomalous. Mean = (0.9 + 0.8) ÷ 2 = 0.85 s. He may have started the stopwatch late, or the car may have hit something.
3
Dina repeats each timing three times. Her friend says one careful timing is enough. Write a reply that gives two reasons.
A stopwatch is started and stopped by a person, so one timing can be wrong. Repeating shows whether the results are similar (reliable) and helps to spot an anomalous result, and the mean of several timings is a better value.
4
Look at Aisha’s graph of speed against coins carried. What does the flat line tell you about the load?
The speed stays about the same however many coins are carried, so the load has little effect on the speed of the car on this ramp.