إعلانيمكن أن تكون علامتك التجارية هناعلامتك التجارية هنافي كل صفحة من Darslab · طلاب وأولياء أمور ومعلمونinfo@darslab.comاسأل عن الأسعارالأسعارinfo@darslab.com
☰ خطة العام · الفيزياء (بالإنجليزية)

Vernier, standards and dimensions

الأسبوع 2 · الفصل الأول «القياس الفيزيائي» (٢): قراءة القدمة ذات الورنية والمعايير القياسية للمتر والكيلوجرام والثانية وصيغة الأبعاد للكميات المشتقة ووحداتها · 3 دروس
1

Reading a vernier caliper

Physics Sec 2 Term 1, Unit 1: pp. 11–15
GoalRead a vernier caliper to 0.1 mm and explain why repeating a reading and averaging helps.
New words
main scale · the fixed scale of the caliper, marked in millimetresvernier scale · the sliding scale whose 10 divisions together are 9 mm longleast count · the smallest amount the instrument can read; for this vernier it is 0.1 mm
Explanation

A ruler reads whole millimetres, but a vernier caliper reads tenths of a millimetre. It has a fixed main scale in millimetres and a sliding vernier scale. Ten vernier divisions fit into only 9 mm, so one vernier division measures 0.9 mm and falls short of a main division by 0.1 mm. That difference, 1 − 0.9 = 0.1 mm, is the least count. To read it: first, read the main scale at the last mark that the vernier zero has passed. Second, find the vernier line that lines up with any line of the main scale and note its number n. Third, add n × 0.1 mm. Always write the unit, and repeat the reading several times; the average of several readings is more reliable than one, because small slips in placing the jaws change from one reading to the next.

Vernier line numberPosition when the vernier zero is at 47.3 mm
047.3 mm
148.2 mm
249.1 mm
350.0 mm: lines up with the main mark 50
Worked examples
The vernier zero is just past the 47 mm mark, and the third vernier line lines up with a main line. Reading = 47 + 3 × 0.1 = 47.3 mm. In other units, 47.3 mm = 4.73 cm = 0.0473 m.
A second case: the main reading before the vernier zero is 12 mm and the eighth line lines up. Reading = 12 + 8 × 0.1 = 12.8 mm. Do not write 12.08: the lines count tenths, not hundredths.
ReadingWidth (mm)
112.4
212.6
312.5
average12.5
Three readings of the width of a key are 12.4 mm, 12.6 mm and 12.5 mm. The average is (12.4 + 12.6 + 12.5) ÷ 3 = 37.5 ÷ 3 = 12.5 mm.
Class activity

Paper vernier, with a grown-up who does the drawing with a ruler and a pencil. Draw a main strip with lines every 1 mm and a second strip with 10 lines spaced 0.9 mm apart. Slide the second strip along the first and find which line lines up for a shift of 0.3 mm, 0.5 mm and 0.8 mm. What do you notice about the number of the lined-up line? Then tie a nut to a string and time ten swings, repeating three times to practise averaging.

Practice
1
Why is the least count of this vernier 0.1 mm?
2
The main reading before the vernier zero is 8 mm and the fifth line lines up. Give the reading.
3
Four readings of a thickness are 5.2, 5.4, 5.3 and 5.3 mm. Find the average.
4
Give a reason to repeat a measurement several times.