AdvertisementYour brand could be hereYour brand hereOn every Darslab page · students, parents and teachersinfo@darslab.comAsk for pricesPricesinfo@darslab.com
☰ Year plan · Physics

Manometers, body pressure and problems

Week 10 · Chapter 5 (B): the manometer, pressure in the body and in a tyre, worked pressure problems (faces of a block, a tank, a manometer, oil in a U-tube) · 3 lessons
3

Solving pressure problems step by step

Physics Sec 2 Term 1, Unit 3: pp. 68–71
GoalSolve pressure problems with four steps and avoid the trap of the arm width.
New words
four steps · write the data in SI, choose the formula, substitute with units, check the answerforce on a base · F = P × A, with P the total pressure and A the areatrap · a mistake that looks reasonable, such as using the width of a U-tube arm
Explanation

Pressure problems have the same four steps. First, write the given data and change every unit to SI (cm² to m², g to kg, cmHg to Pa if needed). Second, choose the formula: P = F ÷ A, P = hρg, P = Pa + hρg or ρ₁h₁ = ρ₂h₂. Third, substitute the numbers with their units. Fourth, check that the size and the unit are sensible. Remember F = P × A when you need the force on a base, and say whether it is from the water alone or from the total pressure. In every task here g = 10 m/s². A trap: in a U-tube the cross-section of an arm does not matter, so the areas in a problem are not used, only the heights.

StepWhat to do
1data in SI units
2choose the formula
3substitute with units
4check size and unit
Worked examples
A 3 kg block has faces of 10 cm × 20 cm and 5 cm × 10 cm. Weight = 3 × 10 = 30 N. On the large face (0.02 m²): P = 30 ÷ 0.02 = 1500 Pa. On the small face (0.005 m²): P = 30 ÷ 0.005 = 6000 Pa. The smaller area gives four times the pressure.
A tank has a base of 0.5 m² under 2 m of water, with an open surface. Water alone: P = 2 × 1000 × 10 = 2 × 10⁴ Pa. Total: 1.013 × 10⁵ + 2 × 10⁴ = 1.213 × 10⁵ Pa. Force on the base: from the total pressure F = 1.213 × 10⁵ × 0.5 ≈ 6.07 × 10⁴ N; from the water alone F = 2 × 10⁴ × 0.5 = 1 × 10⁴ N.
Trap check: in a U-tube, 10 cm of oil (800 kg/m³) is poured into one arm and balances water in the other. Use ρ₁h₁ = ρ₂h₂: 800 × 10 = 1000 × h, so h = 8 cm of water. It makes no difference whether the oil arm is narrow or wide, because pressure depends on height, not on width.
Class activity

Problem workshop, with a grown-up. Take one problem from this lesson, cover its solution and solve it yourself using the four steps on a card. Then change one number (for example the mass of the block or the depth of the tank) and solve again. Check each unit line by line. Swap problems with a friend and mark each other’s work by checking the steps, not only the answers.

Practice
1
Use g = 10 m/s². A 4 kg block rests on a face of 0.01 m². Find the pressure.
2
A tank base of 0.4 m² lies 3 m under water (g = 10 m/s²). Find the force on the base from the water alone.
3
A 20 cm column of oil (800 kg/m³) balances water in a U-tube. What height of water balances it?
4
A pupil uses the arm areas of 1 cm² and 2 cm² in a U-tube problem. What is wrong?