Friction and equilibrium on a rough horizontal plane
Week 7 · Friction: smooth and rough surfaces, static friction and its limit F = μN, kinetic friction, the resultant reaction and the angle of friction (tan λ = μ), and equilibrium on a rough horizontal plane · 3 lessons
1
Smooth and rough surfaces: the normal reaction, static friction that grows up to its limit, and the coefficient of friction μ
Applied Mathematics Sec 2 Term 1, Unit 1, Lesson 5
GoalExplain why friction equals the pull until it reaches its limit F = μN, and use the coefficient of friction.
New words
normal reaction N · the push of a surface on a body, perpendicular to the surfacestatic friction · the force along the surface that stops a body from starting to slidelimiting friction Fl· the largest static friction: Fl = μNcoefficient of friction μ · a number that depends on the two surfaces only
Explanation
A smooth surface gives only a normal reaction N, perpendicular to the surface. A rough surface also gives friction along the surface, opposing the way the body tends to slide. Put a book on a desk and pull it gently with a horizontal force P. It does not move, so the forces balance: the friction F equals P. Pull harder and the friction grows with the pull. This continues only up to a limit, the limiting friction Fl; just beyond it the book slides. Experiments show Fl is proportional to the normal reaction: Fl = μN, where μ is the coefficient of friction (more exactly μs, static). μ depends on the pair of surfaces, rough or polished, dry or wet, but not on the area in contact or the weight; a heavier body only has a bigger N. Usually μ is between 0 and 1, and μ = 0 means a smooth surface. Remember: before the limit the friction F equals the pull, not μN; F = μN only at the point of sliding.
Worked examples
Pull P (N)
What happens
Friction F (N)
0
at rest
0
2
at rest
2
4
at rest
4
6
about to slide
6 (limit)
7
slides
less than 6
A book of weight 12 N lies on a desk and a horizontal pull P is slowly increased. For P = 2 N and 4 N it stays at rest, so the friction is 2 N and 4 N. It just starts to slide at P = 6 N, so Fl = 6 N. N = W = 12 N, so μ = 6/12 = 0.5.
A school bag of weight 40 N lies on a floor with μ = 0.35. Fl = 0.35 × 40 = 14 N. A push of 10 N does not move it and the friction is 10 N (not 14 N). A push of 16 N is more than 14 N, so the bag slides.
The same bag pulled across a polished table with μ = 0.1 needs only 0.1 × 40 = 4 N to start. With μ = 0 (a smooth surface) any pull would make it move.
Class activity
Hook a rubber band on a school bag or shoe and pull it slowly along a desk with a kitchen spring scale held horizontally. Read the scale just before it starts to move. Repeat on a towel. Which surface has the larger μ? Never pull people or vehicles.
Practice
1
A block of weight 25 N starts to slide when the pull is 10 N. Find μ.
μ = 10/25 = 0.4.
2
Same surfaces, a block of weight 40 N. How big is the pull that starts it?
Fl = 0.4 × 40 = 16 N.
3
A crate of weight 80 N and μ = 0.35: find the friction when the pull is 20 N, 28 N and 35 N.
Fl = 0.35 × 80 = 28 N. At 20 N: friction 20 N (at rest). At 28 N: friction 28 N (about to slide). At 35 N it slides.
4
Does μ change if we turn the block on its side so the area in contact is smaller?
No. μ depends only on the two surfaces, not on the area.
5
A student says: “the friction is always μN.” Correct it.
μN is the largest friction (the limit). Before the body is about to slide, friction equals the pull and is smaller than μN.